Electrolux U30130 21602 G Manual de usuario

21602 GGas hobOperating InstructionsGB

10Service and Spare PartsWhen you contact the Service Centre, they will need the following information:1. Your name, address and post code.2. Your t

11Guarantee ConditionsStandard guarantee conditionsWe, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG-Electro

12OVERALL DIMENSIONS Width: 580 mmDepth: 500 mmCUT OUT DIMENSIONS Width: 550 mmDepth: 470 mmSUPPLY CONNECTIONS Gas:R 1/2 inch (1/2 inch male) Rear rig

13BURNER RAPID SEMI-RAPID AUXILIARY(large) (medium) (small)POSITION MAX MIN M AX MIN MAX MIN NOMINAL THERMAL POWER kW 3.0 0.65 2.0

14Important safety requirementsThis hob must be installed in accordance with the Gas Safety (Installation and Use)Regulations (Current Edition) and th

15CLEARANCES REQUIRED WHEN FITTING THE GAS HOBWITHOUT A COOKER HOOD ABOVECLEARANCES REQUIREDWHEN FITTING THE GAS HOBWITH A COOKER HOOD ABOVEFO 0813FO

16A) End of shaft with nutB) WasherC) ElbowFO 0814FO 0264On the end of the shaft, which includes the G 1/2" threaded elbow, adjustment is fixed s

17Cut Out SizeThe dimensions of the cut-out are given in the diagram.Building InBuilding over a cupboard or drawerIf the hob is to be installed above

18ON/OFF SWITCHFLEXOUTLETON/OFF SWITCHFLEXOUTLETFO 0763FO 076412Building over a kitchen unit with doorProper arrangements must be taken indesigning th

19Fitting the hob to the worktopBefore fitting the hob into the cut out,a sealing gasket supplied with thehob must be fitted to the edge of thecut out

2

20Electrical connectionsAny electrical work required to install this hob should be carried out by a qualifiedelectrician or competent person, in accor

21Permanent ConnectionIn the case of a permanent connection, it is necessary that you install a double poleswitch between the hob and the electricity

22Fault FindingPreliminary Electrical Systems CheckSTARTIsolate applianceand carry out:A: Earth Continuitycheck. Has inlet fuse blown?Carry out:C: Pol

23A. EARTH CONTINUITY CHECKAppliance must be electrically disconnected - meter set on W (Ohms) x 1 scale andadjust zero if necessary.— Test leads from

24Check gas supply atburnerIgnition System / Gas IgnitionYESCheck plug top fuse andreplace if necessaryCheck polarity and earthcontinuity of supply po

25CommissioningWhen the hob has been fully installed it will be necessary to check the minimum flame setting.To do this, follow the procedure below.1)

26Conversion from Natural Gas to LPGIt is important to note that this model is designed for use with natural gas but can be convertedfor use with buta

27

35678-5904 03/05Grafiche MDM - Forlì From the Electrolux Group. The world’s No.1 choice.The Electr

3Important Safety InformationYou MUST read these warnings carefully before installing or using the hob. If you needassistance, contact our Customer Ca

4 Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into co

5ContentsImportant Safety Information ... 3Description of the

61. Hob Top2. Rapid Burner3. Semi-rapid Burners4. Auxiliary Burner5. Control knob for back right burner (semi-rapid)6. Control knob for back left burn

7Hob burners control knobs The symbols on the knobs mean that :  there is no gas supply there is maximum gas supply there is minimum gas supplyLight

8Before any maintenance or cleaning can be carried out, you must DISCONNECT thehob from the electricity supply.The hob is best cleaned whilst it is st

9Something Not Working?If the hob is not working correctly, please carry out the following checks before contacting yourlocal AEG-Electrolux Service