Electrolux 2005-04 Manual del operador descargar pdf (Pagina 12)

5. Water Pump and Accessory Carton: Includes

Water Pump (E), Hose Barb (F), Water Valve

(G), 15/16" Wrench (N), Drain Plug (P), Locking

Knob (C) with 5/16" flatwasher, Bearing Caps

with 5/16” Capscrews & Flatwashers.

6. Literature Assembly Envelope

NOTE: Check the carton and all packing filler for loose

parts and optional accessories (if ordered).

IF ANY PARTS ARE MISSING OR DAMAGED, PLEASE

CONTACT YOUR TARGET CUSTOMER SERVICE FOR

INSTRUCTIONS. CALL 1-800-288-5040

• Set the Frame Assembly (2) on a flat surface or on a

TARGET® folding stand.

• Install the Water Pan Assembly (3) between the four

Guides (Q) on the Frame Assembly (2). Locate the

Pan with the Drain Plug (P) at the operating end with

the two Stops located on the bottom of the Pan (3)

straddling the front leg of the Frame. The Water Pan

Assembly (3) should slide freely back and forth on

the Guides (Q) with little lateral movement. Adjust if

needed.

Install the Cutting Head Assembly (1):

1. Set the Cutting Head Assembly (1) on the pivot

bar up between the two Set Collars (A). The

set collars have been pre-set at the factory to

align the blade with the slot in the center of the

cart; it can be adjusted if needed.

2. Using the 5/16” Capscrews and Lockwashers

provided, install the two Bearing Caps (B) to the

bottom of the Cutting Head. Next, tighten the

Capscrews with the wrench provided to securely

hold the Cutting Head (1) onto the pivot bar, but

loose enough so it can be moved up or down.

3. Insert the Locking Knob (C) with 5/16"

flatwasher through the slotted Lockbar (D) into

the tapped hole in the belt guard. This is used

to set the cutting depth of the blade. See

section 5.

Water Pump Assembly (5) Set-up:

1. Remove the Water Pump (E), Hose Barb (F),

the Water Control Valve (G) and Water Tube

Assembly (H) from their carton. Thread the

Hose Barb (F) on the water pump outlet, hand

tighten.

2. Slide the Control Valve (G) onto the flexible plas-

tic tubing and push the open end onto the Hose

Barb (F).

3. Set the Water Pump Assembly (5) in the deep

end of the pan beneath the belt guard. Note:

The water pump inlet screen must be sub-

merged in order to properly pick up water.

4. Place the Water Tube Assembly (H) to the back

of the Blade Guard (J) and insert the two 1/4"

plastic nozzles into the two Ports (I) on the side

of the Blade Guard (J). To prevent interference

with the full movement of the cart, it is recom-

mended that the tubing and electrical cord exit

out the back through the indented area of the

pan.

5. Insert the male plug into the Receptacle (O) on

the motor. The Water Pump (E) will start when

the motor is turned on. For dry cutting, the wa-

ter pump should be unplugged or removed to

prevent damage to the pump.

NOTE: THE MOTOR WATER PUMP OUTLET IS

NOT TO BE USED AS A GENERAL PURPOSE

CONVENIENCE OUTLET. USE FOR CONNECTION

OF THE SUPPLIED WATER PUMP ONLY.

WATER PUMP SAFETY GUIDELINES

Always plug the saw power cord into a GFCI

outlet when using. If a GFCI type outlet is

not available, use a plug-in type GFCI plugged

into a properly grounded outlet. Do not use

any temporary plug adapters.

• The water pump is equipped with a ground electrical

plug, to reduce the risk of possible shock. Be sure

to connect to a properly grounded type receptacle.

• Never pick the water pump up out of the water when

it is plugged in.

• DO NOT EVER use the water pump to pump

anything but water.

• Never service the pump when it is still plugged in.

• Never let the pump operate dry. It is self-cooled by

pumping water. Dry use will cause the pump to fail.

• Maintain regularly and clean out debris from intake

screen.

• Check the power cord for nicks or frays and never

try to alter the power cord in any way.

Install the Cutting Blade:

Always set the Motor Switch to OFF prior to

mounting the blade.

1. Be sure you are using the correct blade for the

material being cut. For example, blades are

available for cutting materials such as wall tile,

quarry tile, marble, slate and similarly hard ma-

terials. For the best results, always use genu-

ine TARGET® diamond blades. Contact your

nearest dealer to select the correct blade for

your specific cutting needs.

2. Rotate the Blade Guard (J) fully up, tightening

the wing nut if needed to hold it in the fully raised

position.

3. Remove the Blade Shaft Nut (L) and the Outer

Blade Flange (M2).

4. Check the blade for Counter Clockwise rotation

(CCW) and install on the spindle shaft.

Rotation direction is indicated by an arrow

on one side of the blade. Make sure the blade

contact surfaces are clean.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Comentarios a estos manuales

Sin comentarios

Electrolux 2005-04 Manual del operador Pagina 12

Comentarios a estos manuales

Relacionado con productos y manuales para Cortadoras De Césped Electrolux 2005-04