Electrolux EFC9740.1 Manual de usuario descargar pdf (Pagina 10)

DISPLAY MEANING OF THE SYMBOLS:

STAND_BY: The motor of the hood is off;

..... first, second , ….speed;

intensive speed activated;

flashing led point: the timer is in action;

(FLASHING F LETTER) grease-filters should be cleaned;

only in case of filtering hood (flashing C letter) carbon filters should be

replaced.

7.1.2 AUTOMATIC CONTROL OF GREASE AND CARBON FILTERS

The electronic controls with display allow automatic control of the grease filters and the carbon

filters (only when the hood is used in the filtering version), so that the user does not have to

remember when maintenance was last carried out.

When the metallic grease filters have to be cleaned, the letter F on the display will flash.

When the carbon filters have to be replaced, the letter C on the display will flash.

It is possible to consult the electronic system concerning how clean the grease filters are and how

worn the carbon filters are, as follows: stop the motor and ...

… to find out how clean the fat filters are, press the O and

- buttons at the same time. On the

display, a number between 0 and 9 will appear, the smaller the number, the dirtier the filter is;

… to find out how worn the carbon filters are, press the buttons O and

+. On the display, a

number between 0 and 9 will appear, the smaller the number, the more worn the filter is.

7.1.3 TO PUT THE GREASE AND/OR CARBON FILTER CONTROL BACK TO ZERO:

• stop the motor (stop position);

• push the push-buttons 0 (zero) and T (timer) at the same time for a few seconds. This symbol

appears

and a “bip“ is issued.

7.1.4 SETTING THE SUCTION /FILTERING USE OF THE HOOD

The hood is delivered standard for suction use (only with flashing F letter). If you wish to use it in

the filtering version (F and C flashing) proceed as follows:

press the buttons

and T on the display for about 5 seconds, the following symbol will

appear followed by a 0.

• At each pressure of the Light Button, it is possible to change the value shown from the O

(suction function), to 1 (filtering function) and viceversa.

• Press the O button (zero) to confirm the choice effected in the previous point.

7.2.1 SOFT TOUCH CONTROLS WITH PUSH BUTTONS SCREENPRINTED ON S/STEEL

(FIG.11b)

WARNING !

To activate the functions connected to these push buttons, it is necessary to

apply a little pressure just lightly and for a short time. If pressure is too lengthy on the

push buttons the connected functions are not activated.

The functions activated by the push buttons are as follows:

LIGHTS: switch the lights on and off;

O MOTOR OFF: turn the motor off;

- reduces the motor speed;

+ increases the motor speed;

TIMER: if pressed when the hood is already functioning with 1st, 2nd, 3rd or 4th

speed, the led point connected with the selected speed, starts to flash for 10 minutes,

after which motor automatically stops.

MEANING OF THE LED POINTS: if the leds connected with the speeds are flashing, there is a

timing running.

1st Speed;

2nd Speed;

3rd Speed;

4th Speed;

5th Speed; led point is flashing;

6th Speed; led point is flashing.

5th and 6th Speed must be used just for short periods as the hood is taking in a big quantity of air

so after 10 minutes the motor is automatically reset to the 3rd speed.

7.2.2 AUTOMATIC CONTROL OF GREASE AND CARBON FILTER

the electronic controls with led points allow automatic control of the grease filters and carbon

filters (only in case the hood is used in filtering version) so that the user does not have to

remember when maintenance was last carried out.

When the grease filters require cleaning, an

acoustic signal is issued for some seconds

and the led point above the timer push

button keeps on flashing.

When the carbon filters need replacing, an

acoustic signal is issued for some seconds

and the led point above the light push

button keeps on flashing.

7.2.3. TO PUT THE GREASE AND CARBON FILTERS CONTROL BACK TO ZERO

To put the grease filter counter back to zero you must:

• stop the motor;

• press the timer push button twice in succession, until you hear the acoustic signal.

To confirm reset the led point stops flashing.

To put the carbon filter counter back to zero you must:

• stop the motor;

• press the light push button twice in succession until you hear the acoustic signal.

To confirm reset, the led point stops flashing.

ATTENTION: The light push button does not switch on/off the lights until you hear acoustic

signal.

7.2.4 SETTING OF THE SUCTION/FILTERING USE OF THE HOOD

The hood is delivered standard for suction use.

If you wish to use the hood in the filtering version, proceed as follows:

• disconnect hood from electricity and then reconnect this to electricity;

• the led-point of the light push button will flash for approx. 10 seconds. During this time press

the light push button 3 times. Three acoustic signals are issued to point out the new setting.

ATTENTION: during the suction/filtering setting phase no function can be activated.

If the hood is set for suction, when connected the led point over the LIGHT Push Button is

flashing. If the hood is set for filtering, when connected the led point over the

TIMER Push Button is flashing.

1 2 ... 5 6 7 8 9 10 11

Comentarios a estos manuales

Sin comentarios

Electrolux EFC9740.1 Manual de usuario Pagina 10

Comentarios a estos manuales

Relacionado con productos y manuales para No Electrolux EFC9740.1