Electrolux ZCV785C Manual de usuario descargar pdf (Pagina 4)

Manual and use

ZCV781, ZCV782, ZCV785

Installation instruction

Plan your central vacuum cleaner construction

Place the central unit and do the air evacuation (air-blow) in the

easiest possible place. On installation in the respective house,

there might be e.g. a valve in the façade. The house might also

be built in the old-fashioned way with bricks – those can be used

as well. Both the aggregate and the blow-out are a noise source;

especially the blow-out might disturb the neighbours. Therefore,

always install the delivered silencer, which clearly minimises the

noise level.

Make sure that there is a separate electric socket, 230V 10A

inactive fuse in close connection to the central unit.

Place the aggregate in such a way that the blow-out-tube is as

short as possible. Blow-out-tubes longer than 5 meters must have

stronger dimensions than the one you have on the suction side.

The aggregate is placed in consideration of simple collection of

the dust bag or dust bag holder – there must be space above or

underneath (see measures picture 1 and 2). Do remember that

a full bag requires a lot of space when collected and you need

space on the side for your hands to loosen the lock respectively

dust bag holder.

Installation of ZCV781, ZCV782 and ZCV785

(see measures – picture 1 and 2)

Turn the mounting plate with the opening upwards and screw it

on with the 4 screws, plugs and/or plaster screws adjusted to the

respective wall material (picture 3).

ATTENTION! The wall plate is delivered with the aggregate and is

found in the same bag as the dust bags.

Hang the vacuum cleaner on the mounting plates in such a way

that the cleaner’s ﬁxing slide down the traces. (picture 4)

The aggregate is provided with 3 connections for intake and 1

connection for blow out. The intake, which is not used, shall be

blocked with the included rubber lock.

The 50mm glued tube system ﬁts directly on the connections of the

aggregate. The 42 mm glue-free requires that you ﬁrst install the

included adapter, which is found in the tube package. (picture 5)

For the installation of the tube system and the vacuum lifting

beams see the separate installation manual.

You can connect the included garage vacuum lifting beam on the

available intake connection. (picture 6)

ATTENTION! If that one is used, an additional dust bag must

be installed. If the garage vacuum lifting beam is not used, the

connection must be blocked with the rubber lock.

In order to connect the blow out, one of the included 90°-angles

is installed on the blow out’s hole. The blow out of ZCV782 and

ZCV785 is the top hole on the backside of the cleaner. The blow

out of ZCV781 is the lowest hole. (picture 7) The 90°-angle may

•

be pointed at any of the holes depending on where you would

like to have your blow out. (picture 8) The connection is adjusted

to a 50 mm tube. In case of a 42 mm tube the included rubber

adapter is installed ﬁrst. (picture 9)

Connect the tube system’s low-voltage-pipe to the aggregate’s

low-voltage-contact. Prior to ﬁxing the cord to the connection, cut

off the top on the rubber spout. Then slip it on the cord with the

top on the cord-side. Peel the cord endings and install the cable

clips. Connect the low-voltage-pipe and slip it over the rubber

spout. (picture 10)

Connect the aggregate to 230V and enjoy your new clean life with

a faster, easier and funnier cleaning.

ZCV781

Three engine protections

1. Vacuum valve (picture 11)

The central unit is equipped with a vacuum valve in order to protect

the engine against overheating in case of a blocked suction hose.

That vacuum valve is located on the side of the central unit and opens

automatically in case of a depression of 25 kPa.

ATTENTION! The vacuum valve must not be blocked or manipulated.

2. Circuit breaker against excess current (picture 12)

In case the engine is exposed to excess current, e.g. at start, the

circuit breaker comes into force. The circuit breaker is restored by

pressing the button under the rubber spout.

3. Overheating protection

In case, for whatever reason, the engine temperature becomes too

high, it remains and can be restarted after cooling down. The reason

might be that the ﬁlter is clogged and therefore the engine gets bad

cooling. The overheating protection is built-in in the engine.

ATTENTION! If this happens the error must be investigated.

Dust collection (picture 13)

The volume of dust collection in model Electrolux ZCV781 is a 22

litres dust bag. A full dust bag minimises the systems performance!

Depending on how often you use your central vacuum cleaner

the dust bag may be collected 2 – 3 times per year – and can be

obtained at authorised Electrolux dealers.

ATTENTION! Vacuum cleaning with ZCV781 must never be done

without installed dust bag.

This is how you change the dust bag:

Remove the central unit’s lock

Loosen the dust bag from the intake tube

Place and press the new dust bag ﬁrmly into the tube. Turn the

bag’s opening to make it lock ﬁrmly on the tube.(picture 14)

Put the lock back on the central unit

•

1 2 3 4 5 6 7 8 9 ... 45 46

Comentarios a estos manuales

Sin comentarios

Electrolux ZCV785C Manual de usuario Pagina 4

Comentarios a estos manuales

Relacionado con productos y manuales para No Electrolux ZCV785C