Electrolux EKM90450X Manual de usuario descargar pdf (Pagina 31)

E 14

25 W - 230 V~

T300°C

Always isolate the cooker from the electricity supply, shut off the gas

supply temporarily and proceed as follows.

- change the injectors,

- adjust the minimum flow of the burners.

REPLACEMENT OF COOKTOP INJECTORS

To change the cooktop injectors, proceed as follows: remove the

grids, remove burners and flame-spreaders (see fig.A), change the

injector (see fig.B) and replace it with another one suitable for the new

type of gas (see table D). Re-assemble everything in reverse order,

ensuring you position the flame-spreader correctly.

Fig. 11

MINIMUM FLOW ADJUSTMENT FOR COOKTOP TAPS

To adjust the minimum, proceed as follows: switch the burner on, and

turn the knob towards the minimum flow position . Remove the knob

from the tap, introduce a small screwdriver in to the tap rod (fig. 11).

Attention: in taps with security valve, the minimum adjustment screw

Z is placed outside the tap rod (fig. 12).

WARNINGS

Isolate the cooker from the electricity supply before attempting to

replace the oven lamp.

The oven lamp is of a special type designed to withstand high

temperatures. To replace it, proceed as follows: remove the protective

glass (A) and replace the burnt-out bulb with one of the same type.

Re-fit the protective glass.

DISMANTLING THE COOKTOP

If it becomes necessary to repair or replace internal components,

proceed as follows: remove the glass lid from its position by sliding

off upwards.

Remove the grids, the burners and flame-spreaders (see fig. 13),

unscrew the visible screws V located on the cooktop (see fig. 14).

Dismantle the cooktop by unscrewing the 4 rear screws A (see fig.

15 ).

Loosen the adjustment screw in order to increase the flow or tighten

it to decrease the flow.

The proper adjustment is obtained when the flame is approximately

3 or 4 mm in length.

For butane/propane gas, the adjustment screw must be fully screwed

down.

Make sure that the flame does not go out when passing quickly from

the max. flow to the minimum flow .

Assemble the knob again.

Fig. 12

Values referred to Hs - 15°C - 1013,25mbar

TAB. D

Cat. II 2H3+

TABELLA GENERALE INIETTORI

Kind of gas

mbar

Nozzle

Burners

Power

KW Consum

N° max. min. max. min.

128

Rapide

3,00 0,75 286 l/h 72 l/h reg.

NATURAL 20 101

Semi rapide

1,75 0,48 167 l/h 46 l/h reg.

G 20 77

Auxiliary

1,00 0,33 95 l/h 31 l/h reg.

141

Triple crown

3,80 1,50 363 l/h 143 l/h reg.

BUTANE 28-30 87

Rapide

3,00 0,75 219 g/h 55 g/h 42

G 30 66

Semi rapide

1,75 0,48 128 g/h 35 g/h 31

Auxiliary

1,00 0,33 73 g/h 24 g/h 27

PROPANE 37 96

Triple crown

3,80 1,50 109 g/h 95 g/h 60

G 31

N°

By pass

C =

injector

Triple crown

GAS ADJUSTMENT

APPLIANCE MAINTENANCE

Fig.14

Fig. 13

TO RAISE AND TO

PUSH IN AHEAD

Fig. 15

1 2 ... 26 27 28 29 30 31 32

Comentarios a estos manuales

Sin comentarios

Electrolux EKM90450X Manual de usuario Pagina 31

Comentarios a estos manuales

Relacionado con productos y manuales para Placas Electrolux EKM90450X