Electrolux AOFP102U Guía para resolver problemas descargar pdf (Pagina 7)

C.1.9.4 REFERENCE STANDARD

The machine can be set to 3 different Standards:

1. Electrolux Food Safe Mode 1

2. Electrolux Food Safe Mode 2

3. U.S. Standard

The default setting for the appliance is the NSF rule number

seven, which states that the product is chilled from 140°F/60°C

to 39.2°F/4°C in 240'.

Standard

Chilling start

temperature

Chilling end

temperature

Chilling tim e

Electrolux Food Safe M1

+145.4ºF

(

+63ºC

)

+50ºF (+10ºC) 110 minutes

Electrolux Food Safe M2

+158ºF (+70ºC) +37.4ºF (+3ºC) 90 minutes

U.S.Standard

CbSt ºC CCEt ºC CCtI minutes

Standard

Chilling start

temperature

Chilling end

temperature

Chilling tim e

Electrolux Food Safe M1

+145.4ºF

(

+63ºC

)

-0.4ºF (-18º C) 270 minutes

Electrolux Food Safe M2

+158ºF (+70ºC) -0.4ºF (-18ºC) 240 minutes

U.S.Standard

CbSt ºC CFEt ºC CFtI minutes

BLAST CHILLER

BLAST FREEZER

Section C.2.2.6 describes how to change the STANDARD (e.g.

to go from the Electrolux Food Safe Mode 1 to the Electrolux Food

Safe Mode 2).

THE REFERENCE STANDARD SELECTION CAN BE

CHANGED ONLY WHEN THERE IS NO CYCLE RUNNING. If a

chilling cycle is running the system will automatically exit the

utility.

The Standard indicator light is normally off. It lights up only when

the Reference Standard option is entered with the UTILITIES

button.

Mode setting "U.S. Standard" is conformed to the requirements

of NSF 7.

Limits are:

NSF 7

- soft chilling = 240 minutes; 140 (+60) / 39.2 (+4)

- hard chilling = 240 minutes; 140 (+60) / 39.2 (+4)

Example of NATIONAL SANITATION FOUNDATION:

A positive blast chilling cycle with probe ends correctly if the

39.2°F (4ºC) is reached within 240'. The chilling then proceeds

either until the maintaining temperature set by the manufacturer

is reached or the user presses STOP.

The user can edit the parameter settings in the U.S. Standard

option (CbSt , CCEt, CctI, CFEt, CftI) either in USER PARAMETERS,

section C.1.9.5, or by selecting the utility directly (see section

below for instructions on how to edit the U.S. Standard

parameters).

Editing USER parameters

To edit a parameter, select the utility:

• press the

button;

• the display blinks to show that the parameter is in ‘edit’ mode;

• press the

buttons to change the value within the

setting range;

• press the button to confirm the settings; if a selection is not

made after 5 seconds, the last value displayed will be confirmed

automatically, or press again.

NOTE: the parameters can be edited ONLY if no cycle is running.

If a cycle is running, the utility will enable only the display of the

parameters.

The system exits the function automatically after 12 seconds if

nothing else is pressed.

C.1.9.5 USER PARAMETERS

For displaying/editing the operating parameters:

• the “TEMPERATURE” display shows the parameter label;

• the “TIME” display shows the value associated to the parameter;

• scroll the parameters;

The system exits the function automatically after 12 seconds if

nothing else is pressed.

C.1.9.6 HACCP

Displays the chamber high temperature alarm and the blast

chilling cycle end error alarm (see section C.4. for all information

on alarms).

C.1.9.7 SERVICE ALARMS

The SERVICE ALARM function stores and displays all the

alarms, except for the chamber high temperature alarm and the

blast chilling cycle end error alarm (see sections C.4.1 for all

information on alarms).

Before using the appliance, clean the chamber with a detergent

solution, as there may still be condensation in the chamber left

over from the final testing by the manufacturers (see section

below for information on the type of product to use).

CLEANING THE CABINET AND ACCESSORIES

It is advisable to clean the chamber every week;

increasing this frequency according

to appliance use.

Before using the unit, clean all the

internal parts and accessories with

warm water and either neutral soap

or products that are over 90%

biodegradable (in order to reduce

the emission of pollutants into the environment),

then rinse and dry thoroughly. Do not use solvent-

C.2 USER INSTRUCTIONS

1 2 3 4 5 6 7 8 9 10 11 12 ... 18 19

Comentarios a estos manuales

Sin comentarios

Electrolux AOFP102U Guía para resolver problemas Pagina 7

Comentarios a estos manuales

Relacionado con productos y manuales para No Electrolux AOFP102U