Electrolux AOFP102U Guía para resolver problemas descargar pdf (Pagina 9)

C.2.2.3 Changing the chilling time

The chilling time can be edited in two situations:

1) when setting a program (P1 o P2)

2) when selecting a chilling cycle.

THE CHILLING TIME CAN NEVER BE EDITED WHEN A CYCLE

IS RUNNING.

To change the time, proceed as follows:

• press the

button for 2 seconds;

• the display blinks to signal that you are in “edit” mode;

• set the value with either the

buttons;

• press the

button to confirm the setting, if a selection

is not made after 5 seconds, the last value displayed will be

confirmed automatically.

C.2.2.4 Changing the chamber temperature during chilling

In custom cycles only, the setpoint can be changed with the

following procedure:

• press the

button for 2 seconds;

• the display blinks to signal that you are in “edit” mode;

• set the value with the

buttons;

• press the

button to confirm the setting, if a selection

is not made after 5 seconds, the last value displayed will be

confirmed automatically.

C.2.2.5 Displaying the temperature setpoint and chilling end

time

When a cycle is running, the user can view the temperature

setpoint and chilling end time by pressing buttons and

simultaneously.

C.2.2.6 Changing the Standard selection

To select a Standard, e.g. the Electrolux Food Safe Mode 2,

press the

button, press the button until the

Standard utility is selected,

press the button to enter, press the button to select

the Standard

either press the button again to

confirm the selection or it will be confirmed automatically if

nothing is pressed for 12 seconds.

C.2.2.7 Editing USER parameters

To edit a parameter, select the utility:

• press the

button;

• the display blinks to show that the parameter is in ‘edit’ mode;

• press the

buttons to change the value within the

setting range;

• press the button to confirm the settings; if a selection is not

made after 5 seconds, the last value displayed will be confirmed

automatically, or press again.

NOTE: the parameters can be edited ONLY if no cycle is running.

If a cycle is running, the utility will enable only the display of the

parameters.

See section D.6 for the “List of user parameters”.

C.2.3 BLAST CHILLING/PRESERVATION CYCLE

When the chilling or freezing cycle has finished, the appliance

will automatically go into the preservation stage. It is important

for the chilled food to be kept in an appropriate way, maintaining

a preservation temperature suitable for the type of food chilled.

C.2.4 DEFROSTING

If the appliance is in the right conditions (indicator light

or or with the appliance on standby), this function

enables a manual defrosting cycle. The display shows the

message “dEfr” throughout the entire cycle.

If a manual defrosting is not possible (during a chilling cycle) the

message “UTIL NONE” will appear on the display.

The selection is enabled only in preservation/maintenance and

when selecting the operating cycle.

When the defrosting is finished the system will go back to the

main configuration. The cycle times and the intervals between

defrostings are preset by the manufacturer.

- Manual defrosting

To start a manual defrosting, proceed as follows:

• PRESS THE

BUTTON; THE DEFROSTING INDICATOR

LIGHT WILL TURN ORANGE, THE REST WILL STAY GREEN.

• PRESS

AGAIN TO CONFIRM.

To shorten the defrosting time, the function can be run with the

door open, or a manual defrosting can be started with the chiller

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 18 19

Comentarios a estos manuales

Sin comentarios

Electrolux AOFP102U Guía para resolver problemas Pagina 9

Comentarios a estos manuales

Relacionado con productos y manuales para No Electrolux AOFP102U