Electrolux AOFP102U Guía para resolver problemas descargar pdf (Pagina 8)

based detergents (e.g. trichloro-ethylene) or abrasive powders

for cleaning. Coat the metal panels with vaseline oil.

The trolleys must be cleaned with high pressure water jets.

Drain off the water used in the process of cleaning by removing

the drain plug at the bottom center of the chamber, so that the

liquid flows out into the drain tray under the cabinet. This tray

must be emptied periodically (AOFP061U, AOFP101U,

AOFP102U models).

Refit the drain plug immediately after the cleaning.

Note: make sure the drain tray has been emptied before

removing the drain plug.

ATTENTION: the AOFP201RU model does not have a drain tray.

Make sure the drain hole is connected to the water drain system.

C.2.1 SWITCHING ON

Switch on the fused disconnet switch or the main circuit breaker

switch and press the I = ON button to start the appliance. The

I = ON indicator light lights up to signal that the appliance is

powered up.

C.2.2 OPERATION

C.2.2.1 Selecting a standard cycle

The default setting on the appliance is the SOFT chilling cycle.

Use these buttons

to select one of the following

options:

From left to right:

• Positive "SOFT CHILLING"

• Positive "HARD CHILLING"

• Positive "COOLER" maintenance (or preservation)

• Negative "BLAST FREEZING" chilling or freezing

• Negative "FREEZER" maintenance (or preservation)

When choosing a cycle, press the

button to move on to the

next option; the options are in a loop and so you can either scroll

forwards

or backwards .

If you want another cycle, keep pressing the

button until

the indicator light for the chosen cycle turns orange, and start it

by pressing the

button.

IMPORTANT:The appliance recognizes automatically when the

food (core) probe is inserted in to the product. If the probe hasn’t

been inserted in to the product, a timed cycle will start

automatically.

It is necessary to wait 2 minutes after the end of the preparation

cycle for the automatic recognition (see section below).

START/STOP CYCLE

This button starts or stops the selected cycle.

The selected cycle starts immediately when enabled. To stop

the cycle, keep the button pressed for at least 3 seconds.

If the door is closed when a cycle is started the button will light

up continuously. If the door is opened during a cycle it will start

blinking continuously.

1- "PREP" To optimize appliance performance when the need

arises, a preparation cycle can be chosen at the beginning of

a chilling cycle which is signalled on the temperature display

by the message “PREP”.

2- If the chiller has been inactive for a long time, the compressor

will be started by impulses to guarantee maximum efficiency.

Consequently, if a timed cycle starts, after 2 minutes the TIME

INDICATOR LIGHT will switch on and the CHAMBER TEMPERA-

TURE will be displayed by default.

C.2.2.2 Selecting a program:

First of all, the user has to decide what kind of cycle to launch

(SOFT, HARD, etc.) and then select the program.

Go through the following steps:

• Select the type of cycle;

• Press the program select button

; the program indicator

light

lights up.

• if the type of program is right, start it by pressing button .

if not

• keep pressing the select button until the chosen

program indicator light

switches on.

• to start the program, press the

button.

The user can edit some of the cycle parameters and save the

changes:

- for blast chilling, the user can edit the chamber chilling time/

setpoint and save it in the memory, from where it can

subsequently be retrieved (see section C.2.2.3 and C.2.2.4).

- for positive maintenance, the user can set the chamber

setpoint.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 18 19

Comentarios a estos manuales

Sin comentarios

Electrolux AOFP102U Guía para resolver problemas Pagina 8

Comentarios a estos manuales

Relacionado con productos y manuales para No Electrolux AOFP102U